eero Pro 6 has slow hardwired speeds with gigabit internet
I am getting slow download speeds on both wired and wifi connections with my new eero 6 Pro setup. On wired ethernet I can get about 400mbps, on wifi about 200mbps. I have gigabit internet with Xfinity BTW. The Internet connection from my router on the eero app shows it delivering 960mbps down. Upload is fine at about 30mbps. Honestly I was expecting a bit more from this product. I see this is a problem in several other discussions but not seeing any suggested fixes, and all kinds of conflicting opinions about what I should expect. If this was normal then why are some users reporting no issues with wired connection while others are having issues?
62 replies
-
Hello rtkramer ,
The eero 6 Pro can push up to 1 gig speeds over WiFi. But this requires optimal setup with minimal interference. Make sure that if you are running multiple eeros that they are at least 35-45ft away from each other. Also review the placement article below to make sure that your eeros are placed optimally.
After we verify that the eeros are placed correctly and placement is not the cause we can start further testing. Can you please answer the questions below?
1) Have you tested the speeds with a device connected to the modem?
2) Do you know if your eero is in a double NAT? If so, it is possible that the upstream router is limiting the speeds you are able to pull through the eero. You can try and put the eero into the upstream routers DMZ or see if you can bridge the upstream router.
3) Are you using the ethernet that came with the eero?
-
Here the same ( Germany )
-
I've been playing around with my triple Eero Pro 6 setup. All my Eero nodes are connected by ethernet. The first thing I noticed is the speed with wired as well as wireless devices was well below my max speed (300mbps). While testing both wired and wireless was struggling at 80mbps. I removed all my Eero's and tested 300mbps so there's definitely something going on with the Eero's.
Besides the drop in speed I also had problems with wired hubs (Philips Hue and Ikea Tradfrir) disappearing and becoming not accessible. After a reset my Ikea accessory are accessible for a limited time. After a while it just becomes non responsive. I also noticed there's a slight delay when opening sites.
Eventually I removed the ethernet cables from all my Eero nodes except the gateway. All my wireless devices are getting a speed of 300mbps (which is the max) and none of my other hubs disappears. In fact, the delay also vanished and are very responsive.
The wired devices however are still getting approx. 25% of my max. speed.
TL;DR:
I removed the ethernet cables from my non-gateway Eero and speed went up. The response time of the wireless devices also became faster. -
I am having the same issue. Good connection to eero, over 900mbps up/down, but 246/184 at ethrnet port and 110/176 wifi right next to the unit. Installation done by Frontier and a technician is coming to the house next week.
-
When my input comes straight from the ISP into Eero, my Eero Pro 6 slows down the wired connections coming out of it, aside from anything it's doing with wireless. A lot...meaning a 33% to 50% reduction.
I have 1 gig 2-way fiber service from CenturyLink.
In my setup, I have a PPPoE feed from CenturyLink, and I updated the firmware such that the Eero can now take a feed using PPPoE instead of the usual DHCP. This functionality was just released with the latest firmware update (see https://support.eero.com/hc/en-us/articles/207852843-Does-eero-support-PPPoE-).
To isolate the problem, compare these two scenarios:
CenturyLink PPPoE Feed ---->. Eero Pro 6 with PPPoE firmware -----> Wired Connection to Laptop: 400-000 mbps
CenturyLinkPPPoE Feed -----> CenturyLink Modem-------> Eero Pro 6 (using DHCP from the modem)------->Wired connection to Laptop: 900 to 950mbps
Same cords, same laptop. In the second scenario, the Eero passes the hardwired signal just fine. In the first scenario, the speed is somehow getting throttled.
I can live with the second scenario but I was really hoping I could eliminate the CenturyLink Modem. I have a TP-Link router than can produce the same results. Something about the way Eero is processing the ethernet feed seems to be the problem.
Any suggestions specific to this case?
-
I have eero wireless 5 pro with EN2251 puma 7 chip. I can't find out if the modem or router make my speed slow and I am not use PPPoe?
-
Update 2/12: tried it with latest update (6.8). Still not fixed. 1/2 usual gigabit speed. Anybody out there? Note this has nothing to do with cabling etc. eero passes through using DHCP just fine from a different PPPoE router. There is something wrong with your PPPoE implementation.
-
Having the same issues 964mps speeds with only getting maybe 400
-
I had the same issue, and for me I fixed it by replacing my switch, which must have developed a fault.
You could also try unplugging and replugging your connection into your switch/router to renegotiate the transfer rate.
Content aside
-
4
Likes
- 1 yr agoLast active
- 62Replies
- 22409Views
-
28
Following