0

eero 6+ setup question

Thanks in advance to anyone who can please help with this question.

I'm unsure how to position and wire in the eero 6+ system. There are a series of cat 6 network cables from each room of a house going into our garage and the fibre modem and an 8 port switch need to stay in the garage because the fibre connection and all the cat 6 cabling from the rooms go into the garage. From reading some threads, our installation plan was to disable the router and wifi functions on the hub supplied by our internet supplier. 

Originally the plan was to plug the cabling in as,

fibre modem with router and wifi functions turned off -> eero6+ no. 1 as main gateway router -> 8 port unmanaged switch -> eero 6+ no. 2 and no. 3. (there are also 3 TVs being hard wired into the switch)

The problem is now the location of the eero6+ would also have to be in the garage and the signal is terrible in that location because of thick concrete walls. I would like to place the first eero6+ no. 1 as main gateway in my living room and I think I have to run a loop of Cat 6 cable from the fibre modem in garage -> living room eero6+ as main gateway router -> back to garage with 8 port switch -> eero 6+ no. 2 and no. 3 in separate bedrooms.

Is there a way I can avoid this? If I leave the router function turned on from the internet supplier, can I go fibre modem with router function left on and WiFi off -> 8 port unmanaged switch -> plug each eero 6+ no. 1, no. 2 and no. 3 into the switch together with the 3 TVs? Is this possible and would that impact performance? Does this mean all 3 eero 6+ will be acting as access points? I read the first eero 6+ should be installed between the modem and the switch and will then handle the routing functions, is that right?

1reply Oldest first
  • Oldest first
  • Newest first
  • Active threads
  • Popular
  • Before finishing reading your post I was already saying out loud, "You need a location with dual drops."  It's that or skin that cat one of several different ways, which all involve additional configuration to be done, but it can be done, assuming you don't want to leave one eero in the garage.

     

    If you bridge your all-in-one from your ISP and want to let an eero handle routing and DHCP but it's in another location other than your distribution frame, then you'd need a location with dual drops to send the data back.  This is why gateways, routers and switches are typically located in an MDF/IDF and wireless access points are on the floor, connected to an ethernet cable to backhaul the data to the swtich(es).

     

    If you just disable the radios on your ISP's all-in-one, you may also want to disable the dhcp server as well unless you put the eeros in bridged mode to avoid being in a double NAT, which isn't that awful if you know what you're doing.  You still get the mesh wireless networking from the eeros by bridging them.  This is my preferred method to keep my router's custom firmware functionality working for me and avoiding generating and issuing new certificates and configurations to connect to my VPN at home through DDNS, giving me secure access to my LAN remotely without having to pay for it.

     

    https://support.eero.com/hc/en-us/articles/207621056-How-do-I-set-up-my-eero-if-I-want-to-keep-my-existing-router-

     

    You could also set the eeros in a DMZ and set up a static route...  Same cat, different method that isn't talked about as much.  :-D

     

    Good luck!  Feel free to update with your experiences after the fact!

    Like
Like Follow
  • 3 wk agoLast active
  • 1Replies
  • 70Views
  • 5 Following

Need Help? We're here for you!

We're big on support, and we want to make sure you always have the best eero experience possible. Here are several resources you can use if you ever need our help!


Quick links

Community Guidelines

Help Center

Contact eero support

@eerosupport

eero.com