How can I connect a 2.4Ghz webcam to eero wifi?
I have a foscam IP webcam that I was able to connect without issue to my old netgear router that provides individual 2.4 and 5Ghz wireless access points. However, with my new eero, I believe the webcam is unable to connect because it is 2.4Ghz only and doesn't understand how to deal with eero broadcasting across both frequencies as one access point. Any solutions out there for this issue?
-
I finally found the solution, in an article by Eero.
———-
You can temporarily disable the 5GHz bands by tapping on Settings > Troubleshooting > 'My device won't connect', then tapping on the "Temporarily pause 5GHz" button. This will disable 5GHz for 10 minutes, which can help with setting up some 2.4GHz only devices.
——
The full (short) article is at Full text is at https://support.eero.com/hc/en-us/articles/115005497223-Can-I-set-my-eeros-to-use-the-2-4-or-5-GHz-frequency-
-
Hmm, wish I could be of more help skdyer but just for info, I have two Ring Doorbells on my Eero network, one is a newer 2.4Ghz/5Ghz model, the other is 2.4Ghz only. Both are working fine and I don’t remember having problems getting either one to connect to the network.
Edit: Out of curiosity I just check connectivity using the Eero app, the 2.4Ghz Ring is of coarse using the 2.4 network, while the 2.4/5Ghz Ring is using the 5Ghz network.
-
I realize this question is a bit dated, but others have more recently had the same question. I have a few 2.4Ghz devices that I need to connect to my network. The resolution that works for me is to utilize an additional wifi router that *does* support 2.4Ghz. Set the 2.4Ghz router to bridge mode and connect it to one of the Eero nodes via an ethernet cable. In my case, I have several older Apple Airport Extreme routers that can operate in 2.4. I can't recall a the moment whether I set separate SSID's for 2.4 and 5Ghz - I'm fairly certain that separate SSIDs are *not* required, but it may be helpful to create separate networks in order to distinguish the two separate networks.
-
Having moved into a new construction home with wifi enabled appliances, I am struggling with the same issue related to the newest model Jenn-Air appliances requiring 2.4Ghz to connect. Does bwgeez02's response and described work-around with the Wifi Analyzer/Connector by farproc remain the most effective option???
-
For anyone using the FEIT Electric smart plugs, the trick is to run setup in AP mode, which will temporarily configure the plug as an access point, which you will then connect to in your phone WiFi settings. It will then magically join your Eero network based on your phones ability to connect to the Eero network. The FEIT documentation wasn’t super clear what AP mode was so I just decided to try it, and it worked like a boss. Good luck y’all!
-
Just walk 50 or so feet away from your nearest access point with your cell phone, in settings go to wifi, forget network, Then find it again and type in network key, and you should be connected to 2.4g. Walk back inside and setup your device. If it doesn’t work the first time try again and walk further. My backyard worked for me. Good luck.
-
There is now a solution to this problem: In the Eero app, go to settings in the lower right, then click on Troubleshooting at the bottom of the list. Click the first item on the list, "My device won't connect." Then click, "Temporarily pause 5GHz." You'll have ten minutes with no 5GHz to do your connecting. Repeat as necessary!
-
I'm throwing a defibrillator on this thread just to say thank you. I've spent a couple hours trying to update an Apple Watch today, and I kept receiving an error message that the watch wasn't connected to the WiFi, even though it was clearly connected. I spoke with two chat reps and took tons of steps before speaking with them and during my conversations with them, all to no avail. The only thing that worked was the temporary disabling of the 5Ghz band on our Eero. As soon as I did that, the update started.
Really appreciate the advice in this thread, as it allowed me to avoid an unnecessary service appointment to fix a problem that didn't exist.
Oh, and a quick update: The app now disables 5Ghz for 15 minutes, rather than 10.